>>>File downloadds:Click here to open
Characteristic
The XL24LE1-D01 is designed with NORDIC’s latest low-cost, high-performance embedded microprocessor-based RF transceiver single-chip nRF24LE1. The NRF24LE1 is a single-chip wireless transceiver system designed for ultra-low-power wireless applications. High-performance microprocessors (compatible with the 8051 instructions) and all high-speed signal processing components associated with the RF protocol are very easy to develop because the link layer is fully integrated into the module.
Automatic detection and automatic retransmission of lost data packets, retransmission time and number of retransmissions can be controlled by software, automatically storing data packets that have not received the response signal; after receiving valid data, the module automatically sends a response signal without additional programming; Carrier detection – fixed frequency detection, built-in hardware CRC error detection and point-to-multipoint communication address control packet transmission error counter and carrier detection function can be used for frequency hopping setting, six channel receiving channel addresses can be set at the same time, and the receiving channel can be selectively opened.
Parameter
Onboard 2.4G PCB antenna, ISM band, 1.27mm in-line, compact size for easy embedded applications.
Supports six channels of data reception (one pair of six)
Working method:half duplex
Supports general modulation methods such as GFSK/FSK
Supports 2Mbps/1Mbps/250Kbps data rate, and can set different transmit power
Multi-frequency point:126 frequency point, meeting the needs of multi-point communication and frequency hopping communication, 2400MHz~2525MHz, 1MHz frequency hopping stepping, channel switching time is about 130us
Internally integrated high PSRR LDO
Wide supply voltage:1.9~3.6V, typical 3.3V
Average emission current as low as 11.3mA (0dBm)
Receive current:about 13mA@2Mbps
Emission current:approx. 11 mA@0dBm
Deep sleep:0.5uA
MCU current:3.8mA@8MHzclock
Built-in Enhanced ShockBurstTM baseband protocol engine
Transceiver data hardware interrupt output
Support 1bit RSSI output
Operating temperature:-20 C ~ 60 C
The best transmission distance:at an open rate of 2MBPS, up to about 50 meters
Chip internal MCU features
16 kB program memory (on-chip Flash)
1 kB data memory (on-chip RAM)
1 kB NV data memory
512 bytes NV data memory
AES encryption HW accelerator
16-32bit multiplication/division co-processor (MDU)
High flexibility IOs
Support for HW debugger
Serves a set of power modes from ultra low power to a power-efficient active mode
Integrated SPI, IIC, UART, 6-12 bit ADC 14 channels, 2 PWM, Watchdog, on-chip oscillator, analog comparator, 3 timer/counters, random number generator, RTC, 18 interrupt sources
Precautions
The wireless module is a static-sensitive device. Pay attention to the static electricity protection when using it. Especially in the dry winter, try not to remove the device on the touch module to avoid unnecessary damage.
The wireless module recommends using a DC power supply with a small ripple, and the operating voltage is recommended to operate at 3.3V.
The grounding of the module should be stable and reliable, and the ground wire should be as close as possible to the power supply. If you use a switching power supply, you must strengthen the retraction to avoid the ripple and spikes of the switching power supply affecting the operating characteristics of the module.
The module uses a PCB antenna. This antenna is easily affected by external circuits. When using it, please do not leave the line or place the device under and around the antenna. If possible, it is best to hollow out. The 2.4G frequency is relatively high, and various materials have certain influences. The general plastic has little effect. If there is a metal object, it will have a significant impact. In this case, it is recommended to use an SMA feeder to connect the SMA antenna.
PIN:PIN NAME:PIN FUNCTIONS
1:REST:Reset
2:P1.4
3:P1.3
4:P1.2
5:P1.1
6:P1.0
7:P0.7
8:P0.6
9:P0.5
10:P0.4
11:P0.3
12:PROG
13:P0.2
14:P0.1
15:P0.0
16:P1.6
17:P1.5
18:VCC:Power Input
19,20:GND:Power Ground
Package includes
5 x Wireless module
Additional information
| Weight | 0.015 kg |
|---|
Reviews